How to Fix a Wooden Garage Door Panel - Woodworking Talk
网页2019年4月10日 · Flathead screwdriver. Wood saw to cut a new piece of panel. Paint and primer. Wood hardener. ¼” lauan plywood or other thin hardwood material. Once you have these items, follow the steps below: Begin cutting out the quarter round on the inside of the garage door by scoring it repeatedly with a utility knife or preferably with an oscillating ...
Large cabinet doors. How to avoid warping | Woodworking Talk
网页2022年6月16日 · A couple of the cabinet companies I install for use them and they seem to help on the larger doors. Cut the panel groove very deep within 1/8" of the edge, then glue in a spline using a hard setting glue (Plastic Resin). Clamp to a flat surface for a couple days. Remill the groove for the panel.
Wooden Garage Doors - Woodworking Talk
网页2007年9月13日 · Im looking to build my own fancy country wooden garage doors, mostly because I am not going to pay someone else to do it. Not sure what I will need though. I think it is built as a solid sheet (8x7) and then cut and braced accordingly. Maybe joined by bisqits and thin plywood backing, all glued and screwed of coarse.
What is the strongest way to join 2x4 with a 2x6 at a 90...
网页2024年7月17日 · Basically - I would attach 2x4 to the top of the wooden garage shelving frame, have it jut out, and then attach a 2x6 (or 2x8) on the face side - at a 90 degree join. Thus, every 4 feet there will be a 2x4 connection with the 2x6 face giving it stability. 1 barn door track would hang on each side of the 2x6.
Custom Wood Carriage Garage Door, How to Refinish?
网页2012年8月18日 · Once the old finish is off, bleach the doors using oxalic acid. This bleach will remove most of the stain from the water. Now sand the surfaces and then prime with a dewaxed shellac (Zinsser SealCoat) and apply 4-6 coats (or the number of coats called for on the label) of a non-poly real marine exterior varnish.
router table/shaper for raised panel doors? - Woodworking Talk
网页2007年8月11日 · i was in the same boat as you about 4 years ago.i went to a wood working show and bought a 3 piece CMT raised panel bit set.It had bits for your rails,stiles and panels.When i make a door if it be paint or stain grade,i use my pocket hole system jig (Kreg tools). i miter the corners and pocket hole one on each corner,then pin nail corners.The …
loose plywood panel in cabinet door - Woodworking Talk
网页2010年2月12日 · It is most unlikely that the plywood will expand or shrink. Just put a glob of glue in the center of the rail and stile. The glue will hold the plywood nice and tight. It also helps to cut the plywood about 1/32" less than the size of the opening in the door holding the plywood. Use the right tool for the job.
How to secure glass in wood frame? - Woodworking Talk
网页2013年2月22日 · I'm putting the finishing touches on a recessed medicine cabinet and I'm trying to figure the best way to install the glass panel in the door frame. The glass sits in a routed channel on the back of the door frame. The glass is 1/8" thick; the routed channel is 3/16" deep x 1/4" wide.
How many amps for garage shop subpanel - Woodworking Talk
网页2021年4月4日 · Rick Christopherson said: a typical garage workshop can operate on as small as a 30-amp subpanel. That would be sufficient to run your full-size dust collector, lighting, and whatever full-size power tool you happen to be using at the time. Only if youre running a really tiny dust collector and/or saw.
Door panels rattle - Woodworking Talk
网页2016年6月6日 · Door panels rattle. I have made hundreds of cabinet doors in my lifetime and never had a problem but the most recent batch I made has rattling panels. The groove in the rails/stiles is 1/4" but the 1/4" panel (sheet goods) is really about 1/32" thinner. I expected the rubber strips (CMT panalign) to keep the panels from rattling but such is not ...