WTB: Atlas Clausing lathe parts - Practical Machinist
网页2009年5月17日 — I have an Atlas Clausing 12x36 lathe, model 111 that I need some parts for. Q526 72-T gear Q530 75-T gear DL455 back gib DL457 crosslide gib I have checked on ebay, but have not found anything for my particular lathe yet. I found a gear on ebay that might work. It is from a Clausing 5914 lathe.
General | Atlas lathe parts, Help - Practical Machinist
网页2010年2月1日 — Good Morning Atlas Sears lathe owners I picked up a Sears 101.07403 lathe a month ago and have been doing some cleaning. LOL It was pretty nasty. oil or grease was like tar. It seem's to run pretty nice except for some extra gear noise. I think I am use to a 1985 Goodway 1640 Lathe I have run for the last 20 years.
General - Archive | SBL vs Logan vs Atlas - Practical Machinist
网页2005年1月25日 — If you have a Craftsman Atlas, a 9 inch South Bend is an improvement. Never underestimate the 9 inch South Bend. Another brand of lathe you might want to investigate is the Sheldon. Sheldon made two or three series of small lathes. They have a ten inch machine and the an eleven inch lathe thst shares parts and the bed wth their …
Antique Machinery and History | My Craftsman Atlas 12 inch lathe …
网页2022年1月20日 — In 1965, I replaced my new in 1954 6" x 12" metal lathe that had made a number of gun parts over the years with a used, circa 1941, Craftsman 12" x 36" metal lathe with Babbitt bearings. I did make a small gun barrel with the big lathe. In 1975, I bought a brand new Craftsman 12" x 36" lathe and an engineer at work bought my old one to do …
Source for Craftsman/Atlas lathe parts? - Practical Machinist
网页2009年6月6日 — I would fuss and make it from cast iron with bronze bushings. If you have a 4-jaw chuck you could even make it on your lathe. I am not familiar with the Atlas/Craftsman lathes but I would hope that it has a better method as a "fuse" for the leadscrew than breaking the bearing bracket. Most lathes in that class have shear pin.
FS 10-12" Atlas lathe parts, gears etc - Practical Machinist
网页2009年3月9日 — Found a box of stuff left over from a 10" F series Atlas lathe I used to have. 17 change gears, only a couple pictured, all in excellent condition, little to no use. Have (3) 20 tooth, (4) 32, (2) 40, (2) 54, (1) 56, and (5) 64 tooth. $8. each, $7. ea 5 or more. NOS headstock idler gear with...
Craftsman (Atlas) Metal Lathe Parts | Garden Tractor Forums
网页2020年6月1日 — Been getting parts for the lathe from Clausing Service Centre since the early 1990's as they offer a lot of the parts for the old Atlas lathes so I emailed a request for a quote for the lead screw, a pair of half nuts and the guide plate for the half nuts this morning.
General | Atlas TH42 Gears | Practical Machinist - Largest ...
网页2022年2月19日 — Diamond. I have no idea what an Atlas TH42 lathe might be. But the gears in the picture appear to be ordinary miter gears, so Boston Gear may have them. The trick is to identify the gear size (diametral pitch and number of teeth) and then look for that size gear. Be prepared to modify the bore and/or hub area.
Atlas/Craftsman 101.07301 - Practical Machinist
网页2018年4月26日 — My machine is a 101. 07301 and also has the 3/8 screw , my thought is that Atlas was using up parts from 37' into 38' and that is how I came up with the date for my machine . Later machines have a Acme screw , none of …
Should I buy the Clausing, Leblond, or near perfect Atlas Metal …
网页2020年12月23日 — The Clausing factory still makes many parts and the parts they dont have they often offer the original drawing so you can make your own. Neither the LeBlond or the lathe shaped object have that going for them. Most of the parts for the Clausing 5914 vari-drive are rebuildable . At one point there was a member here that supplied many parts.