Chevrolet Silverado 2007-2013: 5.3L and 5.7L Vortec Engine …
网页2015年7月9日 — For example, the 5.3L Vortec’s coil-on-plug ignition would eventually replace the distributor setup of all previous small-block engines, the 5.7L included. And while the 5.3L displaces less volume than the 5.7L, it has a shorter bore (96mm vs. 101.6mm) and a longer stroke (92mm vs. 88.4mm) for greater torque and horsepower.
Chevrolet Silverado GMT800 5.3L vs. 5.7L V8 Engine Differences
网页2015年6月22日 — Even though the 5.3 liter engine is smaller, the engines power ratings are similar. The 5.7 rates at 255 hp and 335 ft./lb. of torque. The 5.3's ratings are 270 hp and 315 ft./lb. of torque with later versions increasing horsepower and torque slightly.
Chevrolet Silverado 2007-2013: How to Change Oil
网页2015年6月4日 — Step 7 – Reset oil change warning light. Turn your ignition key to the "Run" position with the engine off. Press and release the gas pedal three times within five seconds. The system is resetting if you observe the "Oil Life Reset" message display for 10 seconds. Turn off the ignition key to the lock position.
Chevrolet Silverado 1999-2006: How to Replace PCV Valve
网页2015年6月11日 — Step 2 – Remove the PCV valve. The PCV valve is located at the rear of the engine on the side nearest to the brake fluid reservoir. The PCV hose is the widest of the three hoses in this location (the two thinner hoses are connected to the firewall). Follow this hose to the valve cover and pull out the hose with attached PCV valve.
Chevrolet Silverado 2007-2013: How to Replace Oxygen Sensors
网页2015年6月8日 — Step 2 – Disconnect O2 sensor from exhaust. Identify the faulty O2 sensor from the code. Bank 1 is on the driver's side, while bank 2 is on the passenger's side. Sensor 1 comes before the catalytic converter, while sensor 2 comes after. Once you've identified the correct sensor, you can get to work.
Chevrolet Silverado 1999-2006: How to Clean or Replace Mass Air …
网页2015年6月11日 — Step 1 – Locate and disconnect the MAF sensor. The MAF sensor is located between the air filter housing and air inlet hose. On top of the sensor, you can see a harness connector situated next to the sensor module. To detach the connector, push down on the tabs and pull it straight out. Figure 1.
Chevrolet Silverado 1999-2006: How to Replace Oxygen (O2) …
网页2015年6月17日 — Step 2 – Remove the old O2 sensors. Figures 4 through 6 below show the replacement of the B2/S2 (passenger's side) O2 sensor. However, replacement of the B1/S2 (driver's side) O2 sensor is the same process. Using your flat head screwdriver, pry out the clip holding the wire harness to the sheet metal. Disconnect the O2 sensor wire harness ...
Chevrolet Silverado 1999-2006: How to Replace Fuel Pressure …
网页2015年6月22日 — Step 4 – Install the new fuel pressure regulator. The new regulator should come with new O-rings and a new metal screen. Figure 6. New fuel pressure regulator. Push the new regulator into place, and make sure the vacuum line port is facing up. Re-install the regulator clamp. Then reattach the vacuum line to the port on the regulator.
Chevrolet Silverado 1999-2006: How to Replace Knock Sensors
网页2015年6月17日 — Pull the manifold off. The knock sensors are located underneath the black plugs connected to a wire harness. Pull the plugs out and unbolt both knock sensors using a 22mm deep well socket. Install the new sensors and torque them to exactly 15 ft-lbs. Apply some RTV to the rubber plugs to prevent water from entering.
Silverado Engine Swap: Forum Newbie Seeks Advice
网页2017年6月20日 — This is true of Silverados with the 4.8 liter V8, which packs “only” 285 hp and 295 lb-ft of torque. That proved adequate back in 2005, but not 2017. So, you can’t blame forum member Conan for coveting the HD’s 6.0 liter engine and its 300hp/360 lb-ft of torque. Then, when Conan began to dream of a Silverado engine swap, he wisely ...